Applied Physics · Precision technologies since 1992
Search

Reviewed October 17, 2026. Educational planning guidance; use the current official chapter, applicable jurisdictional requirements, and qualified facility review for implementation.

USP <797> Air Filtration Is a System Requirement

Air filtration for sterile compounding involves the primary engineering control (PEC), the surrounding environment, air distribution, pressure relationships, and verification. A HEPA filter specification alone does not establish that the work area protects exposed sterile components or meets USP <797>.

Start with the intended compounding scope and the applicable equipment arrangement. The current chapter contains minimum requirements; facility SOPs and engineering decisions implement those requirements rather than replace them. This article summarizes key planning points and distinguishes the tests that answer different air-quality questions.

Air Quality by CSP Category and Equipment Arrangement

Category 1, 2, and 3 compounded sterile preparations (CSPs) require an ISO Class 5 or better PEC. The categories are based on preparation conditions, beyond-use dating, and required controls, not simply on low, medium, or high risk.

Category 3 adds quality-assurance controls supporting longer beyond-use dates. It does not automatically mean a numerically lower ISO room class than Category 2. Sterile hazardous-drug compounding also needs the containment provisions of USP <800>. Check the 2026 official state self-inspection addendum and the current USP chapter before finalizing a layout.

Protect First Air at the Critical Site

The PEC must perform with the intended equipment, supplies, and manipulations in place. First air reaches a critical site from the HEPA-filtered supply without obstruction or contact with a potential contamination source. Hands, containers, or equipment placed in the wrong location can interrupt that protection.

Confirm suitability for the actual task and follow the equipment manufacturer’s operating conditions. A biological safety cabinet, laminar airflow workbench, restricted-access barrier system, and pharmaceutical isolator should not be treated as interchangeable. In particular, a general-purpose cabinet label does not establish suitability for sterile or hazardous-drug compounding.

Use the qualified working configuration as the reference for daily setup. Review proposed additions and moves before changing the arrangement, because placement can affect first air even when the filter and fan are unchanged.

HEPA Selection, Installation, and Integrity

Filter-media efficiency and installed-system leak integrity are different properties. An appropriate filter can still allow bypass at a damaged seal or housing. Conversely, a filter that passes a leak test may not provide the required delivered airflow or acceptable flow pattern at the work area.

For an equipment specification or replacement review, document:

Keep the installed location and filter identity traceable to the test report. An increase in pressure drop can prompt investigation of loading, but it is not an automatic diagnosis or a universal replacement threshold. Review measured airflow, the system design, manufacturer instructions, maintenance history, and the condition of associated components.

Air Changes per Hour and Room-Level Design

USP <797> specifies at least 30 total HEPA-filtered air changes per hour (ACPH) for ISO Class 7 rooms and at least 20 for ISO Class 8 rooms. For both, at least 15 ACPH must come from the HVAC system through ceiling-mounted HEPA filters. The actual rate must be adequate to maintain the required class during dynamic operation.

Where permitted PEC airflow is counted toward the ISO Class 7 total, that contribution and the HVAC contribution must be documented. A PEC relied on for the minimum air-change rate must not be switched off except for maintenance. Have the designer and certifier verify what can legitimately be included; nominal equipment airflow should not be added to a room calculation without that assessment.

ACPH is a volume-flow-to-room-volume relationship. It does not mean that every part of the room’s air is completely replaced each time, and it is not necessarily the outside-air ventilation rate. Supply and return placement, obstructions, occupancy, particle-generating work, temperature, and pressure can affect performance even when the calculated total meets the minimum.

Pressure Differentials and Airflow Direction

Pressure control helps limit movement of lower-quality air into cleaner areas, while hazardous-drug arrangements also address containment. The target relationships must match the complete approved design; “positive pressure everywhere” is not an appropriate rule for every pharmacy.

For a cleanroom suite, USP <797> specifies at least 0.020 inch water column between the anteroom and the unclassified area. Where pressure differentials are required, they must be continuously monitored, and quantitative results reviewed and documented at least daily on compounding days. Review the chapter’s full pressure provisions and USP <800> where applicable rather than applying this one value to every boundary.

Investigate pressure changes with the operating state recorded: door position, occupancy, exhaust operation, fan status, and relevant alarms. A satisfactory spot reading does not explain an earlier excursion or demonstrate that the intended relationship was maintained throughout a shift.

Certification and Airflow Verification

Classified areas, including the PEC, require initial certification and recertification at least every six months. Changes that may affect airflow or air quality, including relevant construction, room reconfiguration, and PEC replacement or relocation, also trigger recertification.

The engineering assessment includes airflow testing, installed HEPA integrity, total airborne particle counts, and dynamic airflow smoke-pattern testing. Required dynamic tests should represent the intended operations and personnel conditions. An at-rest result can provide useful additional information, but it does not substitute for required dynamic testing.

Record equipment and room identifiers, the tested configuration, occupancy, instrument identification and calibration, methods, acceptance criteria, results, and any deviations. The designated person must review the certification records. A report should make clear which tests were performed and under what conditions, rather than presenting only an unexplained pass stamp.

ISO 14644-1 addresses air cleanliness classification by particle concentration; ISO 14644-3 provides cleanroom test methods. These are not general certificates of sterile-compounding compliance. For CGMP manufacturing, FDA also cautions against relying solely on ISO 14644-1 and -2 to qualify an aseptic facility. That manufacturing guidance does not replace pharmacy-specific USP and jurisdictional requirements.

Microbiological Monitoring Is a Separate Evidence Stream

Particle counters measure particles, not whether they contain viable organisms. Microbiological air and surface monitoring, personnel qualification, cleaning, and preparation controls remain necessary alongside engineering certification. Each program has its own applicable methods, frequencies, and review requirements.

A low particle count with an adverse microbial result does not prove the cause is personnel. Investigate possible sources and routes across cleaning, materials, equipment, airflow, personnel, sampling, transport, and laboratory handling. Review trends and context instead of changing a filter or retraining a person solely because one result was unfavorable.

USP’s official FAQs identify ceiling and PEC HEPA-filter changes as events requiring microbiological air and surface sampling. Plan the associated cleaning, testing, result review, and return-to-service decision before maintenance begins.

Airflow Visualization Without Interfering With Other Tests

Tracer visualization helps evaluate how air travels around critical sites and during representative interventions. Define the setup and acceptance criteria, choose useful camera views, and introduce enough tracer to observe the pattern without creating a jet that overwhelms the airflow being studied.

Applied Physics CRF and AP Series foggers support airflow studies. Select the system and delivery configuration for the application. Visualization tracer is different from decontamination chemistry; it should not be described as sterilizing the air or making the room contamination-free.

Do not fog during airborne particle-count measurements: the introduced tracer can be counted by the instrument and invalidate the intended baseline. Conduct the study without exposed patient product and follow an approved sequence for tracer clearance, recovery, cleaning where required, and subsequent testing. Manage any liquid-nitrogen handling and ventilation hazards under the facility’s safety procedures.

Troubleshoot the Whole System

Falling airflow, pressure drift, a leak-test failure, or an adverse monitoring result calls for a documented investigation. Confirm the measurement first, compare the current configuration with the qualified state, examine plausible causes, and record corrective work. Do not assume one symptom identifies one cause.

Before returning an affected area or PEC to use, complete the appropriate requalification and other required checks, then obtain the documented facility review. Filtration equipment supports contamination control; the installed system, operating practices, and continuing evidence determine whether the intended operation remains acceptable.

Primary Sources and Further Reading

Frequently Asked Questions

Does USP <797> require ISO Class 5 air for sterile compounding?

Category 1, 2, and 3 CSPs must be compounded in an ISO Class 5 or better PEC. Surrounding-room requirements depend on the category and equipment arrangement, including specific provisions for pharmaceutical isolators and additional containment requirements for hazardous drugs.

What air-change rates apply to ISO Class 7 and 8 rooms?

USP <797> specifies at least 30 total HEPA-filtered ACPH for ISO Class 7 rooms and at least 20 for ISO Class 8 rooms, with at least 15 ACPH from HVAC through ceiling HEPA filters in both cases. The system must also maintain the required classification during dynamic operations.

How often must classified areas and PECs be recertified?

Certification is required initially and recertification at least every six months. Relevant changes such as construction, room reconfiguration, and PEC relocation or replacement can require recertification before the next routine interval. The designated person must review the records.

Can airflow fogging replace particle counts or microbial monitoring?

No. Airflow visualization, particle counting, and microbiological monitoring answer different questions. Tracer fog can interfere with particle counts, so perform the tests separately under an approved protocol and allow the required clearance and recovery. A fogger does not certify or decontaminate the facility.

You were not leaving your cart just like that, right?

You were not leaving your cart just like that, right?

Enter your details below to save your shopping cart for later. And, who knows, maybe we will even send you a sweet discount code :)

Want to receive personalized offers?

Allow notifications to get real-time updates about your shopping cart and who knows, you may even receive a sweet discount code 😊

Maybe later